RSD01BIW Garage Sectional Door with Extension Spring Mechanism

RSD01BIW residential sectional doors are designed for garages and technical rooms with small-sized door openings with width from 2 000 to 3 500 mm, and height from 1 800 to 3 000 mm. Low lift construction allows installation in premises with minimum headroom and side room clearance of 100 mm. In case there is no space between ceiling, walls and opening edges a built-in installation hardware is available. A wide colour range and numerous door panel designs of RSD01BIW doors make them perfectly suitable for residential dwellings. Doors optimally seal the opening – they protect against cold or hot temperature and humidity nuisance. Easily installed they are durable and have long service life.

Application:

Residential. Garages
Residential. Storerooms

Order with installation

Advantages

The absence of a cold bridge in the sandwich panel, sealing along the entire contour due to seals, and leaf profiles with thermal separation guarantee maximum thermal efficiency of the door.

Large selection of gate panels, more than 100 options in the catalog of design solutions.

Sectional doors are entirely manufactured at DoorHan’s own factories.

The absence of a cold bridge in the sandwich panel, sealing along the entire contour due to seals, and leaf profiles with thermal separation guarantee maximum thermal efficiency of the door.

Large selection of gate panels, more than 100 options in the catalog of design solutions.

Sectional doors are entirely manufactured at DoorHan’s own factories.

Design

Panel Type

Surface Type

Colour Options

M-line

S-line

L-Line

Cassette

V-Line

S-line — inside

Woodgrain (outside)

Stucco (inside)

RAL 9003 (white)

RAL 9006 (silver)

RAL 7004 (grey)

RAL 1014 (beige)

RAL 6005 (green)

RAL 5005 (blue)

RAL 7016 (anthracite)

RAL 7016 (“frost”, extra charge)

RAL 3000 (red)

RAL 3005 (burgundy)

RAL 8017 (brown-red)

RAL 8017 (“frost”, extra charge)

Golden Oak

Wenge

Non-standard color according to RAL card (surcharge)

Equipment

Standard

Optional

Door leaf of 40 mm energy-efficient sandwich panels with reinforcement for hinges and side supports.

Side tracks and vertical angles made of 1.5 mm steel have increased strength and all the necessary perforation.

Galvanized double extension springs («spring-in-spring» system). Door leaf balancing mechanism ensures over 25 000 operating cycles.

Stylish, elegantly shaped handle acts as an elegant decoration of the door leaf.

Low lift guarantees easy installation in premises of almost any size.

A set of mounting hardware, instruction manual and product technical data.

Acrylic window 607 х 202, black (DH85602). Special window design guarantees tight fitting in the door leaf preventing temperature loss. Black framing.

Acrylic window 627 х 327, black, industrial (DH85603). Special window design guarantees tight fitting in the door leaf preventing temperature loss. Black framing.

Acrylic window 452 х 302, white (DH85626). Special window design guarantees tight fitting in the door leaf preventing temperature loss. White framing.

Acrylic window 452 х 302, brown (DH85631). Special window design guarantees tight fitting in the door leaf preventing temperature loss. Brown framing.

Acrylic window 452 х 302, white with “cross design” (DH85627) decorating insert. Special window design guarantees tight fitting in the door leaf preventing temperature loss. Cross-shaped insert. White framing.

Acrylic window 452 х 302, brown with “cross design” (DH85628) decorating insert. Special window design guarantees tight fitting in the door leaf preventing temperature loss. Cross-shaped insert. Brown framing.

Acrylic window 452 х 302, white with “diamond design”(DH85629) decorating insert. Special window design guarantees tight fitting in the door leaf preventing temperature loss. Diamond-shaped insert. White framing.

Acrylic window 452 х 302, brown with “diamond design” (DH85630) decorating insert. Special window design guarantees tight fitting in the door leaf preventing temperature loss. Diamond-shaped insert. Brown framing.

Latch lock (R25135) blocks the door leaf from inside the premise. Simple and reliable.

T-lock blocks the door leaf both from inside and outside the premise.

The additional external contour of the seal ensures maximum adherence of the web to the seal. The air chamber formed between the seals provides the best sealing, preventing cold from penetrating into the room.

The “thermal package” option involves installing a heat-resistant lower (upper) aluminum profile using T-bridge technology, which avoids heat loss.

Automation. Possibility of automating the gate with a drive (see section “Automation”).

Technical description

Size Table

Opening Dimensions

Construction

Standard Construction

Specifications

Operating Conditions

Packaging

Parameters

Value

Opening height, mm

1 800–3 000

Opening width, mm

2 000–3 500

Headroom, mm

minimum 100

Sideroom clearance, mm

minimum 100

Steel profile with multi-chamber top seal
Multi-chamber side seals
Bottom steel profile with thermal break and bottom seal
Top corner bracket
Side support with adjustable roller holder
Bottom corner bracket with adjustable roller holder
Hinge
Vertical track
Horizontal track
C-profile
Sandwich panel
Double pulley bracket
Universal mounting bracket for horizontal tracks
Handle
Latch lock (optional)
Extension springs

Low lift (extension springs)

Symbol, parameter name	Calculation formula
H, mm Opening height	H
h, mm Headroom height	h ≥ 100; (h ≥ 130 if door operator is used)
B, mm Opening width	B
A, mm Angle track height	H + 54
A1, mm Vertical track height	А - 552
E, mm Horizontal track length	Н + 440
S, mm Minimum side room clearance	100
P, mm Door opener position	Н + 1 185
n, mm Clear opening	230 (without door operator); 40-60 (with door operator)

Parameter	Value	Notes
Thermal resistance, m² · °С/W	1,13 (А)	depends on door size, listed for 3 500 × 3 000 mm door
Noise insulation, dB	24 (А)
Wind load, Pa	460 (В)
Number of cycles	25 000
Force of manual opening and closing, N	150
Water resistance at pressure change, Pa	250
Air permeability, m³/m²*h	4,9
Door leaf weight, kg/m²	11,6	depends on type and size of door panels

Door leaf should smoothly slide vertically along the tracks, and be properly balanced, i. e. extension springs should compensate leaf weight.

For opening the door in manual operation use only the door handle.

Do not lift too much force when opening/closing the door. Prevent any sharp movements of the door.

Keep people and animals clear of opening while door is operated.

Never stay or cross an opening under a moving door leaf as it may cause serious injury or death.

Don’t strike the door leaf or obstruct its movement.

Keep tracks and rollers clean, as dirt may prevent the door from smooth movement and cause overloading and damage of the door opener (if used).

Keep the door opening clear of any objects and litter as it may unbalance and jam the door leaf.

Packing in cardboard	Packaging features
Description	the door leaf and the tracks system are packed in a fibre board and polystyrene combination wrapped in a stretch film. Hardware is packed in a box wrapped in a stretch film. All packages are labeled with stickers containing order information and DoorHan logo
Contents	corrugated fiberboard, polystyrene, stretch-film, adhesive tape
Width, mm	from 500 to 800
Height, mm	from 300 to 500
Length, mm	from 2 100 to 3 600
Gross weight, kg	up to 100
Number of items in the packaging	leaf package — from 3 to 5 panels; tracks package — 1 track system; hardware — 1 box

Additional Information print

Sandwich panels should be stored in producer’s packaging on a flat horizontal surface in warehouses or under a canopy for a period not exceeding 6 months from the production date. Provide proper protection from water, snow, dirt, and direct sunlight.

Installation

Mounting Options

Checking Dimensional Details

Overhead or classical mounting. All the tracks are mounted on the inner side of headroom and siderooms.

Butted mounting (in case there’s no sideroom). Such mounting involves installation of tracks system on a supporting bar butted up against the opening. Arising wall unevenness is leveled with corner and pulley brackets. Supporting bar has aesthetic appearance and can be coloured white (RAL 9003) and sepia brown (RAL 8014).

Overlapping built-in mounting (in case there’s no sideroom). Supporting bar is installed in the opening with 20 mm overlapping. Tracks system is mounted on the bar. Arising wall unevenness is leveled with corner and pulley brackets. Supporting bar has aesthetic appearance and can be coloured white (RAL 9003) and sepia brown (RAL 8014).

All the necessary measurements are taken inside the premises with just a measuring tape and a water level. Every dimension should be taken at least in three points:
H — opening height (distance from floor to opening top);
B — opening width (distance between left and right side of the opening);
h — headroom (distance between opening top and ceiling) min 100 mm;
b1/ b2 — left/right sideroom (distance between a corresponding opening edge and obstacle) min 100 mm;
L — backroom.
When measuring Н and В the largest figure is taken for final dimension.
When measuring h, b1, b2 and L the smallest figure is taken for final dimension.
Difference of floor level along the opening should not exceed 10 mm. Make sure that mounting surface of headroom and side rooms is level. The inside perimeter of the door opening should be framed with metal or other solid material in case the surface is not concrete or solid enough to install tracks system.

Warranty print

DoorHan warrants to the original purchaser of the product that the sandwich panels and steel profiles of the track system will be free from corrosion for a period of ten years.

New Products

New colors of sandwich panels - RAL 8017 and RAL 7016 with a matte surface with a frost effect.

A unique warm gate circuit based on multi-chamber seals reduces heat loss in the room and prevents freezing.

Fully thermally separated fabric - warm bottom profile, warm panel.

Multi-stage gate security system - double cable system, “spring in spring” system.