Showcase roller shutters made of foam-filled profile RH58N

This model is usually used to protect windows and display cases. Thanks to the high heat-saving and sound-insulating properties of the RH58N foam-filled profile, roller shutters reliably protect the room from the effects of adverse weather conditions and the penetration of sunlight and extraneous sounds.

Application:

Large window facades and shop windows in shopping and entertainment centers

Order with installation

Design

Colours

White

Brown

Grey

Beige

Green

Blue

Burgundy

Silver

Equipment

Standard

Optional

Box assembled. It is an assembled protective box with side covers, a shaft and capsules, and a control mechanism — manual or automatic.

The canvas is assembled. Canvas made of foam-filled profile with side locks that prevent the profile from diverging.

End profile with seal. Locking mechanisms can be installed in the end profile.

Set of guide profiles with seal. A large selection of standard and reinforced guides allows you to select profiles for roller shutter systems installed on openings of any size, taking into account wind loads and burglary resistance requirements.

Manual or automatic drive.

Box with complete set.

Two-position rocker switch SWB for controlling the drive in both directions of travel.

Key-button SWM for sending a control command to the electric drive control unit by turning the key.

Control unit CV01 for remote control of one roller shutter or a group of roller shutters.

SMARTROLL control unit for remote control of internal roller shutter electric drives using DoorHan remote controls.

ROLL1/ROLL2 blocks for remote control of internal roller shutter electric drives using DoorHan remote controls.

Group control unit GC2/GC4. GC2 for controlling two drives from one switch; block GC4 - to control four drives.

External radio receiver DHRE-1 for controlling automation from other manufacturers using the DoorHan remote control.

WI-FI module for wireless control (generation of a control signal, NO) of electric drives.

GSM module for receiving a signal from a mobile phone and transmitting a control command to start the electric drive.

T5 remote control for controlling five roller shutters.

TRANSMITTER 4 remote control for remote control of four automatic devices.

TRANSMITTER 4-PRO-BLACK remote control for remote control of four automatic devices.

Safety photocells PHOTOCELL-N, consisting of an infrared transmitter and receiver.

Technical description

Size Table

Opening Dimensions

Construction

Standard Construction

Specifications

Operating Conditions

Packaging

Parameters

Value

Opening height, mm

from 500 to 5,500

Opening width, mm

from 500 to 3,500

Maximum door curtain area, sqm

Headroom, mm

from 165 (surface mounting)

Sideroom clearance, mm

from 65 (surface mounting)

Side cover RK165, RK180, RK205, RSK230, RK250, RK250S, RK300, RSK300, RK375
Bearing support BS100, BS42
Guide device RU65
3a. Guide roller RU77 (RV77)
Bearing BR28, BR42
Universal capsule KP60, KPU60, KPU70, KPU70S
Octagonal shaft RV60-1, RV60, RV70
Crossbar ring RD60, RD70
Protective box RB165, RB180, RB205, RB230, RB250, RB300, RB375
Automatic lock RM2, RM3
Intrashaft electric drive
BU100K drive mounting plate
Guide profile RG65MS, RG65S, RG70MS, RG70S
Plug PB14
Side lock SLA58, SL58M
End profile RA50EM, RA58KN
Profile (canvas) RH58N
Key lock switch SWM, SWK

Roller shutters with manual belt, cord or cord drive <br>An easy-to-use belt inertial drive is installed on roller shutters with a leaf weight of up to 15 kg. The roller shutter canvas rises and falls due to the tension of the tape. The cord drive is installed on roller shutters with a leaf weight of up to 20 kg. It is controlled by rotating the handle of the cord stacker. The cord drive lifts roller shutters with a web weight of up to 40 kg through the use of a durable steel cable. The operating principle is similar to a cord drive.

Roller shutters with manual belt, cord or cord drive
An easy-to-use belt inertial drive is installed on roller shutters with a leaf weight of up to 15 kg. The roller shutter canvas rises and falls due to the tension of the tape. The cord drive is installed on roller shutters with a leaf weight of up to 20 kg. It is controlled by rotating the handle of the cord stacker. The cord drive lifts roller shutters with a web weight of up to 40 kg through the use of a durable steel cable. The operating principle is similar to a cord drive.

Roller shutters with a manual crank drive <br>The crank drive allows you to lift roller shutters with a leaf weight of up to 30 kg. When the knob is rotated clockwise, the blade rises, and counterclockwise, it lowers.

Roller shutters with a manual crank drive
The crank drive allows you to lift roller shutters with a leaf weight of up to 30 kg. When the knob is rotated clockwise, the blade rises, and counterclockwise, it lowers.

Roller shutters with a spring-inertia mechanism <br>The spring-inertia mechanism is used for roller shutters with a leaf weight of up to 60 kg. Roller shutters are easily lifted manually and quickly lowered under their own weight due to the fact that the weight of the roller shutter is balanced by a torsion spring mounted on the shaft.

Roller shutters with a spring-inertia mechanism
The spring-inertia mechanism is used for roller shutters with a leaf weight of up to 60 kg. Roller shutters are easily lifted manually and quickly lowered under their own weight due to the fact that the weight of the roller shutter is balanced by a torsion spring mounted on the shaft.

Parameter	Value	Notes
	RH58N
Material	Aluminium, foam
Slats weight, kg/rmt	0.128
Slats weight, kg/sqm	2.20
Number of slats per 1 m of curtain height, pcs	17
Maximum door curtain width, m	3.5
Maximum door curtain area, sqm	11

Properly installed and operated roller shutters guarantee reliable and durable operation. To extend the life of your roller shutters, follow these instructions:

1. Installation of roller shutters and roller shutters must be carried out by qualified specialists who have been trained by the DoorHan concern.

2. Installation of the product must be carried out strictly in accordance with the installation instructions for roller shutters and technical documentation of the DoorHan concern.

3. Roller shutters should open smoothly without jerking or jolting.

4. To raise and lower structures, use only controls designed for this purpose.

5. Do not use more than 100 N force to open the roller shutters.

6. Partial raising or lowering of the roller shutter leaf is not recommended, especially for large structures (size more than 3,000 × 2,000 mm).

7. If a mechanical lock or latch is used in the design, lifting the blade when the lock is closed is prohibited.

8. When using a cardan drive, when rotating, the knob should be held at an angle of 45°. According to EN 12453 or 12604, a manual force of 390 N is permissible. In the case of large roller shutters, the emergency manual drive (hinge, cardan) is only suitable for closing.

9. When using an automatic drive, follow the instructions supplied with the drive.

10. Keep children away from roller shutter control devices (buttons, remote controls).

11. Make sure that people and animals are not within the range of the roller shutters while they are opening or closing.

12. It is strictly prohibited to stand under the structure while it is in operation, as this can lead to injury.

13. Do not subject the roller shutters to impacts or interfere with their free opening and closing.

14. Make sure that while moving the roller shutter leaf there are no foreign objects in the opening, as this may lead to damage to the structure.

15. It is prohibited to install additional equipment or accessories, as well as to independently replace or adjust individual parts, without consultation with the manufacturer (consultation is considered to be a request that contains a clear description of the problem that has arisen, which can be documented).

16. In winter, in case of icing of parts of the roller shutter or roller shutter structure, before raising and lowering the canvas, it is first necessary to tap the structure along the contour until the parts of the structure are completely free of ice, paying special attention to the condition of the junction of the bottom strip of the product with the window sill or floor, they also must be cleaned.

17. It is necessary to carry out regular maintenance of roller shutters, at least once a year.

18. If roller shutters are used for purposes other than their intended purpose or the dimensions of which exceed those recommended by the manufacturer, the manufacturer is not responsible for their integrity and proper operation.

19. Diagnostics and repair of roller shutter or roller shutter structures should be carried out only by qualified specialists.

Packing in cardboard	Packaging features
Description	Roller shutter packaging consists of bubble film and five-layer white cardboard; the canvas and the box are wrapped in bubble wrap, then wrapped in cardboard to form a box; The cardboard packaging is covered with 2 layers of stretch film on top and secured with tape with the company logo
Width, mm	from 165 to 375
Height, mm	from 165 to 375
Length, mm	from 500 to 6,000

Additional Information print

For entrance, garage and through openings, as well as in areas with high wind loads, only roller shutters from profiles of the RH77 and RHE84 series are installed.

Installation

Mounting Options

Checking Dimensional Details

Face of wall mount. The most popular type of installation which doesn’t require time-consuming preparation of the slopes and niche for the shutter box. Shutter box with curtain is installed above the opening and the guide rails — on either side of the opening. Closed rolling doors completely cover the opening and are almost flush with the walls.

Between jambs mount, shutter box outward. All the rolling shutter components are installed inside the door or window opening. The window or door itself should open inward the premises.

Between jambs mount, shutter box inward. The rolling shutter is installed inside the opening with the shutter box turned inward so that the curtain is flush with the opening outside surface.

Hidden mount. Hidden mount needs a special niche to be done in the upper part of the opening. The niche is designed at the stage of building construction or renovation. The hidden method of installation allows you to place the shutters inside the opening and when opened they do not prevent the windows from opening in any direction.

Measuring parameters for surface mounting:
H — opening height (max), mm;
B — opening width (max), mm;
h — lintel height (min), mm;
b1 and b2 — right and left lateral distances (min), mm.
Measurement parameters for built-in installation:
H — opening height (min), mm;
B — opening width (min), mm.
To take measurements you must use a tape measure, building level or electronic measuring instruments. It is recommended to measure each parameter at a minimum of three points. When measuring the opening for structures mounted in a built-in way, you should take into account the unevenness of the walls and adjust the measurements downward by 5-10 mm
Prepared openings must meet the following requirements: openings must be rectangular in shape; the surface of the opening planes must be flat and smooth, without sagging plaster and cracks; the wall must be monolithic, without voids (concrete, metal, solid brick); if the brick is hollow, it is recommended to edge the opening with a metal corner; the internal and external planes of the walls at the junction of structures must be smooth, without protrusions and depressions; deviations of working surfaces from vertical and horizontal should not exceed 1.5 mm per meter, but not more than 5 mm, the difference in diagonals should not exceed 5 mm.

Warranty print

The buyer is provided with a performance guarantee for roller shutter systems produced by the DoorHan concern for a period of 1 year from the date of purchase of this product. In case of damage to the paintwork as a result of the influence of climatic factors, natural phenomena, the release of fine solid particles or other aggressive substances, corrosion from scratches and chips that occur during operation, the warranty for the paintwork becomes invalid.

New Products

New steel side covers RS137 and RSK300, made of galvanized steel, have high anti-corrosion properties and strength characteristics, and are painted in the color of the box.

New reliable packaging in white five-layer cardboard.

Expansion of the range of end roller shutter profiles - profile RA58KN015. The new end profile is black and is more economical compared to the RA50EN.